REL-FO/LD-110DC/2X21/MS - Single relay

1308326

Plug-in miniature relay with mechanical switching position indicator, FASTON connection, 2 changeover contacts, status display: LED (yellow), Freewheeling diode, Input voltage: 110 V DC

This product needs further products for operation. Mandatory accessories

Notes on operation	Do not use to separate SELV/PELV circuits from other circuits, because safe isolation is not guaranteed. (applies to the optocoupler variants)
Notes on operation	The outputs are not suitable for switching different outer conductors.
Notes on operation	The system installer must ensure the touch protection of the product (at voltages > 25 V AC/60 V DC). The product is a built-in device without protection against direct contact.

Product type	Single relay
Product family	ESSENTIAL edition
Operating mode	100% operating factor
Mechanical service life	approx. 5x 10⁷ cycles
Relay type	Electromechanical relay
Insulation characteristics: Air clearances and creepage distances between the power circuits
Insulation	Basic insulation
Overvoltage category	II
Pollution degree	3
Data management status
Date of last data management	03.07.2025

Maximum power dissipation for nominal condition	0.73 W
Test voltage (Winding/contact)	5 kV_rms (50 Hz, 1 min., winding/contact)
Test voltage (Changeover contact/changeover contact)	3 kV_rms (50 Hz, 1 min., changeover contact/changeover contact)
Test voltage (open contact)	1 kV_rms (50 Hz, 1 min., open contact)
Air clearances and creepage distances between the power circuits
Rated insulation voltage	250 V AC
Rated surge voltage	2.5 kV

Coil side
Nominal input voltage U_N	110 V DC
Input voltage range	77 V DC ... 121 V DC
Drive and function	monostable
Drive (polarity)	polarized
Typical input current at U_N	6 mA
Input power dissipation for U_N	0.66 W
Typical response time	2 ms ... 10 ms
Typical release time range	5 ms ... 20 ms
Protective circuit	Freewheeling diode
Status display	LED (yellow)
Coil resistance	18870 Ω ±10 %

Switching
Contact switching type	2 changeover contacts
Type of switch contact	Single contact
Contact material	AgSnO
Maximum switching voltage	250 V AC
	30 V DC
Minimum switching voltage	5 V (10 mA)
Limiting continuous current	8 A
Maximum inrush current	16 A (20 ms, N/O contacts)
Inrush current, minimum	10 mA (5 V)
Interrupting rating (ohmic load) max.	192 W (24 V DC)
	240 W (30 V DC)
	2000 VA (250 V AC)

Connection method	FASTON connection

Width	13 mm
Height	31.1 mm
Depth	34 mm

Ambient conditions
Degree of protection (Relay)	RT II (Relay)
Degree of protection (Installation location)	IP54 (Installation location)
Ambient temperature (operation)	-40 °C ... 70 °C
Ambient temperature (storage/transport)	-40 °C ... 70 °C
Altitude	≤ 2000 m

Standards/regulations	IEC 61810-1
	IEC 60664-1
Air clearances and creepage distances between the power circuits
Standards/regulations	IEC 60664-1

Mounting position	any

Item number	1308326
Packing unit	10 pc
Minimum order quantity	10 pc
Sales key	C460
Product key	DKF937
GTIN	4063151558826
Weight per piece (including packing)	26.2 g
Weight per piece (excluding packing)	26.2 g
Customs tariff number	85364900
Country of origin	CN

Compatible products

Mandatory accessories

ECLASS-13.0	27371601
ECLASS-15.0	27371601

EU RoHS
Fulfills EU RoHS substance requirements	Yes (No exemptions)
China RoHS
Environment friendly use period (EFUP)	EFUP-E No hazardous substances above the limits
EU REACH SVHC
REACH candidate substance (CAS No.)	No substance above 0.1 wt%

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

REL-FO/LD-110DC/2X21/MS - Single relay

1308326

Product details

ECLASS

ETIM

cUL Recognized

UL Recognized

Compatible products

Automate

Connect

Mark, assemble, and install

Supply, charge, and protect

Switch, Measure and Monitor

REL-FO/LD-110DC/2X21/MS - Single relay 1308326

Product details

ECLASS

ETIM

Compatible products

ECOR-1-BSC2/FO/2X21 - Relay base 1308332

REL-FO/LD-110DC/2X21/MS - Single relay

1308326